82# Ecotec Valve Springs & Titanium Retainers
ZZPerformance is constantly striving to make modifying your car more affordable and more reliable. Our latest product, 82# valve springs, does both. These springs are compatible with all Ecotec 2.0, 2.2, 2.4 liter Ecotec engines. .500" coil bind, 82# seat pressure 200# at .420" lift Currently only available with titanium retainers.
Ask Question Product Questions
Are these the valve springs & retainers that you guys recommend to use with your LSJ performance cams ?
Question by: Douglas on Sep 4, 2016 11:36:00 PM
Yes this is what we would suggest to use with our cams.
Ryan D (Admin) on Sep 7, 2016 2:53:00 PM
Will these springs work fine with stock cams and lash ajusters?
Question by: Jordan Canter on Jun 1, 2015 1:06:00 PM
Yes, they will work great with the stock cams. They will allow you to bump the rev limiter to 7500 rpm and shift higher for a better average power.
Tim Beek (Admin) on Jun 2, 2015 10:19:00 AM
What is the closed ft lbs for valve springs #82 in spring and retainer kit
Question by: Ralph on Jan 25, 2017 10:22:00 PM
Closedseat pressure is 82#'s.
Ryan D (Admin) on Jan 26, 2017 9:36:00 AM
It says highly modified valve train for Stg 3 SC camshafts. Can I use these springs with your Stg 3 cams, built rods,NBS, ATI and get the full potential out of your cams?
Question by: Shannon on Apr 20, 2016 5:39:00 PM
Yes, that combination will work fine.
Steve Hickman (Admin) on Apr 21, 2016 12:51:00 PM
With full supporting mods how high can we rev the engine @ 20lbs of boost with a TVS1320?
Question by: Shannon on Apr 20, 2016 10:21:00 AM
that really depends on cams, neutral balance shafts, rods, etc etc. the springs are good to over 8K.
Steve Hickman (Admin) on Apr 20, 2016 5:01:00 PM
On an 07 l61 2.2l with a 75 shot i want to reach 7.5k do i need balance shaft delete for that or can i do it with just these springs
Question by: Layce baker on Feb 26, 2017 9:20:00 AM
You would need 82# valve springs, Neutral Balance Shafts, and Forged Rods and Pistons to rev that high.
Kyle D (Admin) on Feb 28, 2017 11:43:00 AM
When will these be back in stock?
Question by: Patrick Hardee on Feb 16, 2017 5:42:00 PM
These are currently in stock. Please redirect all stocking questions to firstname.lastname@example.org
Ryan D (Admin) on Feb 17, 2017 2:57:00 PM
I am ordering your LNF 1.0 PCM. When I order it I'm also ordering these springs. Can my pcm be pre tuned to bump up the rev limit?
Question by: Tyler on Oct 13, 2016 2:57:00 PM
If you leave a note, we could raise the rev limiter for them, however without larger cams and a turbo, you will not need to rev the car any higher. The valve springs are still a great upgrade though, because the stock springs can valve float on basic setups.
Tim Beek (Admin) on Oct 17, 2016 12:45:00 PM
Can you use tge oem spring seats? I have a 2.2
Question by: Bryan on Dec 10, 2015 2:49:00 PM
Our springs install just like stock. No special seats required
Zoom Iwuagwu (Admin) on Dec 14, 2015 2:46:00 PM
Two questions will these work with stock cams? Also are these the same as oem just titanium retainers?
Question by: Chris on Oct 6, 2016 10:28:00 PM
Yes, these will work with stock cams. And no they are not the same as stock. They are made to fit our 82# valve springs specifically.
Ryan D (Admin) on Oct 7, 2016 11:00:00 AM
Do they come in the set of 16? When I put it in the cart it says back order but on the catalog part they are in stock?!
Question by: Jen on Jun 7, 2016 6:28:00 PM
You get a full set, they are in stock.
Zoom Iwuagwu (Admin) on Jun 8, 2016 11:51:00 AM
Will these springs handle the GM performance cam set? Part number 88958648 with the following specs
Duration @ 0.050" lift is 247° on the intake and 249° on the exhaust
Maximum lift is 0.499" for the intake and 0.499" on the exhaust
Lobe centerline is 116°
Question by: Colton on Nov 14, 2015 10:29:00 PM
No, these springs bind at .500 so they would not work as you need some room
Zoom Iwuagwu (Admin) on Nov 15, 2015 5:14:00 PM