Engine & Trans Mount Spacers

Suspension & Brakes - Engine & Trans Mount Spacers

Engine & Trans Mount Spacers

28 reviews
Regular price $24.99
/
  • In stock, ready to ship
  • Inventory on the way

Did you lower your car and now have the dreaded axle wobble when you take off from a stop? These 3/8" spacers install on the studs of the stock 3800 series II and III engine and transmission mounts and will help get closer to the stock axle angle. They might not fix every car, but they sure help. However moving the engine and trans upwards will bring them closer to the hood, so make sure you have enough hood clearance to install them.

They raise the engine and trans 3/8".

 

Will not work in LS4 or H-Body applications.

Customer Reviews
4.4 Based on 28 Reviews
5 ★
61% 
17
4 ★
18% 
5
3 ★
21% 
6
2 ★
0% 
0
1 ★
0% 
0
Customer Photos
Write a Review Ask a Question

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
  • hardware
  • part
  • W-Body
  • engine
  • vibration
  • sticker
  • mount
  • bottom
  • holes
  • transmission
DB
09/07/2022
David B.
United States

Definitely recommend.

Spacers work great! I had shorter dog bones installed while I found time to put these in and I could feel a difference. The spacers made the car drive better over the dog bones. I did have to open up the holes in the spacers, because they were slightly too close together. I also added locktite to the threads when I put the nuts back on, because there's not too much thread left on the mount with the spacer installed. All in all, I would recommend these over shorter dog bones.

LP
03/09/2022
Logan P.
United States United States

double stacked lifters on a very low impala

the way the engine sits on a factory impala has the transmission pan hanging below the subframe, and I hit my transmission on a reflector and cracked it. A bit of custom fabrication allowed me to double stack these while replacing the transmission, and now the pan hangs safely above the subframe. double stacking was fairly simple on the transmission side, as the holes just needed to be widened slightly with a drill bit, then one spacer goes on the top stud, and one goes on the bottom studs. the motor side was a bit different as the mounting holes are different for the bottom. to solve this, I simply welded the spacer to the subframe where the mount sits, and added a 3/8" nut on the original studs that go through the subframe. great product, could've saved me $800 if I bought them sooner.

ZZPerformance Engine & Trans Mount Spacers ReviewZZPerformance Engine & Trans Mount Spacers ReviewZZPerformance Engine & Trans Mount Spacers Review
RS
01/27/2022
Robert S.
United States United States

Trans mount spacer

The holes didn't line up. I had to drill it wider by about 1/8 inch.

DS
05/07/2021
Denis S.
United States United States

Power logs

Fit and finish was great could use better Hardware

WB
04/09/2021
Will B.
United States United States

Deff. Buy if your on coils!

No more vibration

ZZPerformance Engine & Trans Mount Spacers Review
ZZP W-Body Coilovers
$999.99
25 reviews
Suspension & Brakes - ZZP WBody Lowering Springs Gen2
Suspension & Brakes - ZZP WBody Lowering Springs Gen2
ZZP WBody Lowering Springs Gen2
$139.99
41 reviews
Suspension & Brakes - ZZP Billet Dog Bones
Suspension & Brakes - ZZP Billet Dog Bones
ZZP Billet Dog Bones
from $64.99
12 reviews
Suspension & Brakes - ZZP Shorter Billet Dog Bones
Suspension & Brakes - ZZP Shorter Billet Dog Bones
ZZP Shorter Billet dog bones
$129.99
36 reviews
ZZP Adjustable Sway Bar Links
$99.99
8 reviews
Sold Out
Suspension & Brakes - ZZP Tubular Control Arms For Wbody
Suspension & Brakes - ZZP Tubular Control Arms For Wbody
ZZP WBody Tubular Control Arms
$519.99
5 reviews
Recently viewed