ATI GM Ecotec Super Damper

917287 $408.99
Model
Regular price $408.99

Underdrives are currently out of stock, but they should be back in stock late March '19.

ATI's support of front-wheel-drive drag racing continues to grow with our latest Damper for GM's popular 4 cylinder Ecotec engine. Ecotec Dampers feature all factory serpentine grooves machined into the outer shell, allowing them to be used in both race and street configurations.

Top Ecotec racers like Nelson Hoyos and Marty Ladwig rely on ATI Super Dampers for superior performance and reliability race after race. In May of 2005, Marty Ladwig's ATI equipped Chevy Cobalt became the first 4-cylinder FWD drag car to break 200 MPH in the 1/4 mile with a blistering 202.02 MPH run.

Supercharged Applications
The ATI Super Damper works with either a six or eight groove setup with no modification. While the stock setup only requires a six groove pulley system, the ATI Super Damper features a lightweight 2024 aluminum outer shell designed to accommodate 8 groove belts commonly found on aftermarket superchargers.


ENGINE


DAMPER
PART #


OUTER
DIAMETER


WEIGHT


SHELL MATERIAL


RIBS


HUB # [1]


HUB
MATERIAL


4 CYL ECOTEC


917287


6.78" (5% OD)


6.75 lbs


ALUMINUM


8


916752


STEEL


917288 [2]


5.5" OD (12% UD)


4.50 lbs


ALUMINUM


8


916753


STEEL


[1] All hubs have 3/16 key @ std SB 10° location. 8 groove shell for supercharged upgrades, OEM 6 groove location.
[2] Damper is 12% UD from stock; not for over 600 HP on the street.
[3] Damper is 5% OD from stock

Under drive is recommended for turbo applications. It will help avoid over spinning your alternator and its better than stock dampening will allow for high rpm engine reliability

Over drive is recommended for supercharged applications. It will increase blower speed the same as dropping 1 pulley size so it's recommended to run a larger pulley on the blower than we normally recommend. However due to the larger diameter of the pulley you will either want to grind a little extra clearance for the belt or you can run our Machined front cover .

Note: Since the size of the balancer is changed you will need a longer belt for the overdrive pulley and a shorter belt for the underdrive pulley. An LNF with the under drive balancer will need a K050390 belt.

To install the damper:

    1. Use a stop on the flywheel to prevent the engine from turning.
    1. Push your stock damper all the way on to the crank to align the oil pump gear with the key on the damper.
    1. Pull off the stock damper.
    1. Line up the keyway and push the ATI damper on the crankshaft - it will only go on 1/4 inch or so.
    1. Since the ATI damper is press fit, you will need to use the damper installation tool to press the damper on the rest of the way, WITHOUT TURNING THE CRANKSHAFT. --- If the crankshaft turns the damper will not go into the oil pump gear, and you will have to start over again.
    1. We use sealer to stop oil from leaking through the keyway and out past the damper bolt.

 

Also referred to as: Harmonic Balancer, Damper, or Crank pulley


Torque the damper bolt to 74ft-lbs plus 75 degrees with blue loctite on the bolt.

Underdrives are currently out of stock, but they should be back in stock late March '19.

ATI's support of front-wheel-drive drag racing continues to grow with our latest Damper for GM's popular 4 cylinder Ecotec engine. Ecotec Dampers feature all factory serpentine grooves machined into the outer shell, allowing them to be used in both race and street configurations.

Top Ecotec racers like Nelson Hoyos and Marty Ladwig rely on ATI Super Dampers for superior performance and reliability race after race. In May of 2005, Marty Ladwig's ATI equipped Chevy Cobalt became the first 4-cylinder FWD drag car to break 200 MPH in the 1/4 mile with a blistering 202.02 MPH run.

Supercharged Applications
The ATI Super Damper works with either a six or eight groove setup with no modification. While the stock setup only requires a six groove pulley system, the ATI Super Damper features a lightweight 2024 aluminum outer shell designed to accommodate 8 groove belts commonly found on aftermarket superchargers.


ENGINE


DAMPER
PART #


OUTER
DIAMETER


WEIGHT


SHELL MATERIAL


RIBS


HUB # [1]


HUB
MATERIAL


4 CYL ECOTEC


917287


6.78" (5% OD)


6.75 lbs


ALUMINUM


8


916752


STEEL


917288 [2]


5.5" OD (12% UD)


4.50 lbs


ALUMINUM


8


916753


STEEL


[1] All hubs have 3/16 key @ std SB 10° location. 8 groove shell for supercharged upgrades, OEM 6 groove location.
[2] Damper is 12% UD from stock; not for over 600 HP on the street.
[3] Damper is 5% OD from stock

Under drive is recommended for turbo applications. It will help avoid over spinning your alternator and its better than stock dampening will allow for high rpm engine reliability

Over drive is recommended for supercharged applications. It will increase blower speed the same as dropping 1 pulley size so it's recommended to run a larger pulley on the blower than we normally recommend. However due to the larger diameter of the pulley you will either want to grind a little extra clearance for the belt or you can run our Machined front cover .

Note: Since the size of the balancer is changed you will need a longer belt for the overdrive pulley and a shorter belt for the underdrive pulley. An LNF with the under drive balancer will need a K050390 belt.

To install the damper:

    1. Use a stop on the flywheel to prevent the engine from turning.
    1. Push your stock damper all the way on to the crank to align the oil pump gear with the key on the damper.
    1. Pull off the stock damper.
    1. Line up the keyway and push the ATI damper on the crankshaft - it will only go on 1/4 inch or so.
    1. Since the ATI damper is press fit, you will need to use the damper installation tool to press the damper on the rest of the way, WITHOUT TURNING THE CRANKSHAFT. --- If the crankshaft turns the damper will not go into the oil pump gear, and you will have to start over again.
    1. We use sealer to stop oil from leaking through the keyway and out past the damper bolt.

 

Also referred to as: Harmonic Balancer, Damper, or Crank pulley


Torque the damper bolt to 74ft-lbs plus 75 degrees with blue loctite on the bolt.

You are viewing a product listed on the following platforms:

Ecotec
Slingshot