AEM Water/Methanol Injection Kit

$465.89 

4



This variant is currently out of stock

Intercooling - AEM Water/Methanol Injection Kit
Intercooling - AEM Water/Methanol Injection Kit

We now carry two different version of the AEM Water/Methanol Injection Kit. We have a MAP (manifold absolute pressure) version and then a MAF (mass air flow) version to dial in the injection. Read the descriptions below to figure out which kit best suites your needs. If you need any assistance email customerservice@zzperformance.com. 

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing - without using high-octane racing fuel - for power gains of up to 20%. AEM's Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system. 

  • Boost Dependent and Multi-Input (0-5v/frequency) progressive controller designs feature large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs
  • Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, integrated pump ground circuit and additional wire for optional on/off fluid solenoid
  • “Boost Safe” failsafe output included (for complete failsafe under all conditions, see our Water/Methanol Failsafe Device)
  • Heavy-duty high-pressure injection pump features integral fittings, a Santoprene diaphragm and EPDM seals to resist corrosion. Our pump maximizes line pressure for optimum atomization and its quiet, smooth operation is almost undetectable
  • Precision-machined billet-aluminum injector with integral check valve
  • Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min)
  • 1.15-gallon tank with anti-starvation reservoir, integral conductive low-fluid sensor and positive lock connector (tank-less systems available)
  • 20 feet of injection tubing included
  • LED dash light for system status and low fluid warning

  • MAP based details:

     

    The on-demand progressive controller in AEM's Boost Dependent PN: 30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine's power curve. 

    AEM's engineers spent extensive time developing the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engines need for water/methanol injection, which further optimizes charge air cooling and detonation control.

    The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

    AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

    AEM's Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System's compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness.

    MAF based details:

    The AEM controller with kit 30-3350 features a multiple input design that enables users to install AEM's Water/Methanol Injection Kit on ultra-high boost vehicles (above 35 PSI) using a 0-5v voltage-based external MAP sensor.

    Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing (without using high-octane racing fuel) for power gains of up to 20%. AEM's Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

    The new AEM controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back. Both controller housings feature an easy to access integrated fuse and molded mounting tabs.

    AEM’s Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

    Legal in California - only for racing vehicles, which may never be used upon a highway. 

    Important Safety Notice Regarding Methanol

    AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component. 

    All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems. 

    Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol. 

    WARNINGImproper installation and/or adjustment of this product can result in major engine/vehicle damage. For technical assistance visit our forum or visit our dealer locator to find a professional installer/tuner near you. 

    Note: AEM or ZZPerformance holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. 

    Additional Notes: For optimum results, all water/methanol injection systems and gauges should be run with an AEM inline filter (AEM Part #30-3003). ZZPerformance has only seen performance gains with Methanol injection when running mixes of over 50% methanol to water ratios. The car should be dyno tuned on the Dyno to dial in the AFR for your setup and nozzle size. 

    Intercooling - AEM Water/Methanol Injection Kit
    Intercooling - AEM Water/Methanol Injection Kit

    Customer Reviews

    5 Based on 4 Reviews
    5 ★
    100% 
    4
    4 ★
    0% 
    0
    3 ★
    0% 
    0
    2 ★
    0% 
    0
    1 ★
    0% 
    0
    Write a Review Ask a Question
    • Reviews
    • Questions

    Thank you for submitting a review!

    Your input is very much appreciated. Share it with your friends so they can enjoy it too!

    Filter Reviews:
    PR
    05/16/2019
    Patrick R.

    Detailed

    Clear and concise installation instructions .Good quality parts.

    GG
    07/25/2018
    Guest G.

    Perfect product

    Just what i bought super easy installation

    TH
    04/09/2018
    Tommy H.

    Graet kit

    Great product easy to install works very well just need to get a check valve and then retuned

    GG
    04/20/2016
    Guest G.

    Great service from zzp

    Great service from zzp